Panasonic VIERA TC-P50G25X Operating Instructions Manual

Panasonic VIERA TC-P50G25X Operating Instructions Manual Manual pdf 8 page image

14 15Quick StartGuide First Time SetupFirst Time SetupFirst time setup screen is displayed only when the TV is turned on for the first time after the power cord isinserted into a wall outlet and when “Auto power on” (p. 33) is set to “No”.or Turn the TV On with the POWER buttonor(Remote)(TV)Configure your viewing modeSelect your languageLanguage / Idioma / LangueEnglish Español FrançaisStep 1 of 6 / Paso 1 de 6 / Étape 1 de 6OKSelectSelecciónSélectionselectOKSelect your viewing mode (Be sure to select “Home use”)Step 2 of 6RETURNOKSelectSet viewing modeHome use Store DemonstrationPlease select your viewing environment.Select “Home Use” when using this TV in yourhome.selectOKPlease confirm your selection (Home Use) before pressing OK button.If you select “Store Demonstration” by mistake in ,confirmation screen will be displayed.NoYou are selecting the store demonstration mode.If you select “Yes”, the picture mode will regularly resetto “Vivid” and a Picture Refresh message will be displayed on thescreen.Yes selectOKSelect “No” and return to previous screen .If you select “Yes”, Screen enters the store demonstration mode.To display the “Set viewing mode” screen again as shown above and select“Home Use”, do one of the following:• Press and hold down the side POWER button for at least five seconds.• Unplug power cord for 30 seconds and plug it again.Noteis not available on - .is not available on .When you have used to turn the TV off, the next time you turn the TV on the“Language” settings will be displayed.If you use any other step other than to turn the TV off, or if you used the EXITbutton to quit before completing the settings, the next time you turn the TV on “Firsttime setup” will not be automatically displayed.• The settings up to that point are saved.• You can reset the settings using “First time setup”. (p. 33)To change the setting (Language, ANT/Cable setup, Input labels, Clock) later, go tothe Menu screen (p. 33)Press to return tothe previous screenNoteAbout broadcastingsystemsAnalog (NTSC):ConventionalbroadcastingDigital (ATSC):Newprogrammingthat allowsyou to viewmore channelsfeaturinghigh-qualityvideo and soundAuto channel setup (ANT/Cable setup)Select the connected Antenna in terminalANT/Cable setup Step 3 of 6Select “Not used” when viewing TV viaSatellite receiver or Cable box. Note: Select“Cable” when viewing via Cable DTA Box.AntennaCable InCable Antenna Not usedANTENNACable InRETURNOKSelectselectOKNot used: Go to(Label inputs)Select “Not used” when no wire is connected to the “Antenna/Cable” terminal.Typical when a Cable/Satellite box is connected to a TV input.Prevents accidental tuning to an unavailable signal.Select “Start”Auto program Step 3 of 6Start scanning for channels via the TV’sbuilt-in tuner. Select “Skip” when viewing TVchannels via Satellite receiver or Cable box.RETURNOKSelectStart Skip selectOKSkip: Go to(Label inputs)Start scanning the channels(Available channels are automatically set.)Auto programProgressNumber of analog channelsNumber of digital channelsPress RETURN to quit8%100RETURNComplete the Auto program setupCompletion message is displayed when the Auto program scan is successfully completed.Auto programAuto program completed.Press OK to continue.Number of analog channelsNumber of digital channels100OKRETURNOKIf there is no availablechannel, return to -(ANT/ Cable setup).“Not used” will be selected.Select the Input labels (Label inputs)Select NEXT then press OK to go to the next step.Label inputs Step 4 of 6Press RIGHT to select a label for each input.Example: DVD, Blu-ray, etc. or “Not used”.Press RED to customize the label.HDMI HDMINot usedRETURNChangeSelectHDMI 3 GAMEComponent 1Component 2Video 1Video 2 GAMEPCNextHDMI 1HDMI 2Edit labelR G B Yselectset orSelect or enter thconnected to theHDMIRETURNOKSelectNext1 @.4 GHI7PQRS2 ABC5 JKL8 TUV3 DEF6 MNO9WXYZ0 - ,LASTR G BABC abcGAMEHDMIVideo 2PCNextGAMEFollow the instructions onscreen to complete thefollowing operations.Label: [BLANK] Not used/Blu-ray/DVD/DVD REC/HOME THTR/GAME/COMPUTER/VCR/CABLE/SATELLITE/DVR/CAMERA/MONITOR/AUX/RECEIVER/MEDIACTR/MEDIA EXT/OTHEROperation of the EXIT button during “First time setup”Press the button once to display confirmation screen. Press again to closeconfirmation screen.[EXIT confirmation screen]Are you sure you want to exit the First Time Setup?To repeat the First Time Setup, select“First time setup” in the Setup Menu.Yes NoYes Exit “First time setup”No Return to the original screen.