Panasonic TX-24MS480B Operating Instructions Manual

Panasonic TX-24MS480B Operating Instructions Manual Manual pdf 17 page image

English - 16 -may vary depending on the operator and the ScanMode selections. Set the Scan Mode as Full if youdon’t know how to set up other options. Highlight Scanand press OK to start the scan. You can press the Backbutton to cancel the scan. The channels that havealready been found will be stored in the channel list.Single RF Scan: Enter the Frequency value. SignalLevel and Signal Quality of the selected Frequencywill be shown. Highlight the Scan option and pressOK to start scan. The found channels will be storedin the channel list.LCN: Set your preference for LCN. LCN is the LogicalChannel Number system that organizes availablebroadcasts in accordance with a recognizable channelnumber sequence (if available).Channel Scan Type: Set your scan type preference.Channel Store Type: Set your store type preference.Favourite Network Select: Select your favourite net-work. This menu option will be active, if more than onenetwork is available. This option may not be availabledepending on the selected country during the initialsetup process.Channel Skip: Set channels to be skipped whenswitching the channels via Programme +/- buttonson the remote. Highlight the desired channel/s on thelist and press OK to select/unselect.Channel Swap: Replace the positions of the twoselected channels in the channel list. Highlight thedesired channels on the list and press OK to select.When the second channel is selected, the position ofthis channel will be replaced with the position of thefirst selected channel. You should set the LCN optionto Off or Default in order to enable this feature.Channel Move: Move a channel to the position ofanother channel. Highlight the channel you want tomove and press OK to select. Then do the same for asecond channel. When the second channel is selected,the first selected channel will be moved to the positionof that channel. You should set the LCN option to Offor Default in order to enable this feature.Channel Edit: Edit channels in the channel list. Editthe name and channel number of the selected channeland display Network Name, Frequency, Colour Sys-tem, Sound System, Modulation and Symbol Rateinformation related to that channel. Depending on thechannel other options may also be editable. You canpress the Blue button to delete the highlighted channel.Analogue Channel Fine-tune: Fine-tune an analoguechannel. A list of available analogue channels will bedisplayed. Select the desired one from the list andpress OK button. Then change the frequency of thechannel by pressing Left/Right directional buttons.Press OK to store the new frequency for that channel.Press Back to cancel. This item may not be visible,depending on whether or not the last watched channelwas analogue.Clear Channel List: Delete all channels stored in thechannel list of the selected channel installation mode.A dialogue will be displayed for confirmation. HighlightOK and press OK button to proceed. Highlight Canceland press OK to cancel.Channel Installation Mode - Preferred/GeneralSatellite/SatelliteSatellite Re-scan: Start a satellite scan beginningwith the operator selection screen for the PreferredSatellite channel installation mode or with the satelliteselection screen for the General Satellite or Satellitechannel installation mode. When this scanning optionis preferred, some scanning configurations will not beavailable and thus the preferences you made duringthe initial setup process may not be changed.Satellite Add: Add satellite and perform a satellitescan.Satellite Update: Search for any updates by repeatingthe previous scan with the same settings. You will alsobe able to configure these settings before the scan. IfChannel Installation Mode is set to Preferred Satel-lite this option may be named differently depending onthe available services. Highlight the satellite and pressOK button to configure detailed satellite parameters.Press the Right directional button to proceed.Satellite Manual Tuning: Start a manual satellite scan.Favourite Network Select: Select your favourite net-work. This menu option will be active, if more than onenetwork is available. This option may not be availabledepending on the selected country during the initialsetup process.Channel Skip: Set channels to be skipped whenswitching the channels via Programme +/- buttonson the remote. Highlight the desired channel/s on thelist and press OK to select/unselect.Channel Swap: Replace the positions of the twoselected channels in the channel list. Highlight thedesired channels on the list and press OK to select.When the second channel is selected, the position ofthis channel will be replaced with the position of thefirst selected channel.Channel Move: Move a channel to the position ofanother channel. Highlight the channel you want tomove and press OK to select. Then do the same for asecond channel. When the second channel is selected,the first selected channel will be moved to the positionof that channel.Channel Edit: Edit channels in the channel list. Edit thename and channel number of the selected channel anddisplay Network Name, Frequency, Colour Systemand Sound System information related to that channelif available. Depending on the channel other options