Panasonic TX-24MS480B Operating Instructions Manual

Panasonic TX-24MS480B Operating Instructions Manual Manual pdf 13 page image

English - 12 -DVBS Configuration Setting screen will be displayednext. First Antenna type(*) should be set. Universal,Single Cable and Jess Singlecable options areavailable. Set the Antenna Type as Universal forDirect and DiSEqC satellite systems. If you set theantenna type as Universal, press the Right directionalbutton to proceed to the next step. If the antennatype is set as Single Cable or Jess Singlecable,there will be three more additional options on theDVBS Configuration Setting screen: Tuner, Bandfrequency and User Defined. User Defined optionwill be available if the Band frequency is set as UserDefined. Set these options if available and press theRight directional button to proceed.(*) This option may be named as Satellite type depending onthe country selection.Depending on the country and satellite type selectionsyou made in the earlier steps of the initial setupprocess, Load Preset List screen may be displayednext. Highlight Load Preset List and press OK or theRight directional button to proceed with the SatcoDXinstallation. You can also skip this step by selectingSkip option.After the parameters on the DVBS ConfigurationSetting screen are configured according to yourenvironment and preset list installation preference isselected the next step may be Select Satellite screen.You may be able to set up different satellites dependingon the selected antenna type and operator in theprevious steps. Highlight the desired satellite optionand press OK to set the parameters(*). The SatelliteStatus of the first satellite option will be set as On. Inorder to configure other settings of the satellite and toenable scan this option should be set as On first. PressBack button and select next satellite you want to set.After you completed the configuration changes, pressthe Right directional button to proceed.(*) If you have a Direct satellite system, DiSEqC Set optionshould be set as DiSEqC A.If Load Preset List option is selected in the previousstep next steps will be skipped and the preset channellist installation will start. If the correct satellite has notbeen selected for SatcoDX installation, a warningdialogue will be displayed on the screen. The satellite/sthat can be selected will be listed. Press OK to closethe dialogue and then set the satellite accordingly.Channel Scan screen will be displayed next. SelectScan and press OK or the Right directional buttonto proceed with the scanning configurations. SelectSkip Scan to proceed without performing a scan andcomplete the initial setup.DVBS Scan Configure screen will be displayed nextif Scan option is selected. Following options will beavailable: Scan Mode and Channels. You can chooseto perform a full scan or a network scan. Set theScan Mode accordingly. If you are going to perform anetwork scan, make sure that you have adjusted theFrequency, Symbol Rate (Ksym/s) and Polarisationparameters under the Transponder option accuratelyon the Satellite Setup screen. You may not be ableto change the Scan mode setting depending on theprevious selections. If the Channels option is setas Free encrypted channels will not be installed.Additional options may also be available dependingon the selected operator, configure these settingsaccording to your preferences. Once you are donewith setting the available options, press the Rightdirectional button to start scan while Scan Mode orChannels is highlighted. While the search continuesyou can press the Back button to cancel the search.The channels that have already been found will bestored in the channel list.When the initial setup is completed results will bedisplayed. Press OK to finish the setup.Next, you will need to agree to the terms and conditionsof Freeview Play to make use of the related services.Scroll the page to read the entire text using the up/down directional buttons. Highlight Accept and pressOK on the remote to confirm and proceed. HighlightSkip and press OK to proceed without confirmation.For further requirements for Freeview Play servicesrefer to the Freeview Play Platform section.Home Screen will be displayed. You can highlight LiveTV app and press OK to switch to Live TV mode andwatch TV channels.Home ScreenTo enjoy the benefits of your Android TV, your TV mustbe connected to the Internet. Connect the TV to ahome network with a high-speed Internet connection.You can connect your TV wirelessly or wired to yourmodem/router. Refer to the Network & Internetand Connecting to the Internet sections for furtherinformation on how to connect your TV to the internet.The Home menu is the centre of your TV. Press theHome button to display Home Screen. From theHome menu you can start any application, switch to aTV channel, watch a movie or switch to a connecteddevice. Depending on your TV setup and your countryselection in the initial setup the Home menu maycontain different items.The available options of the Home Screen are positi-oned in rows. To navigate through the Home Screenoptions use the directional buttons on the remote.Apps, YouTube, Google Play Movies & TV, GooglePlay Music and Google Play related rows and rows ofthe applications you have installed might be available.Select a row then move the focus to the desired itemin the row. Press OK button to make a selection or toenter a sub-menu.On the upper left of the screen, search tools will belocated. You can choose either to type a word to start