Panasonic TC TC-P58S1 Operating Instructions Manual

Also see for TC-P58S1 - 58" Plasma TV: Quick setup guide Specifications Service manual Manual de instrucciones

Panasonic TC TC-P58S1 Operating Instructions Manual Manual pdf 29 page image

29AdvancedHow to Use Menu Functions(picture, sound quality, etc.)Adjustments/Configurations (alternatives)Sets the mode to select the channel with Channel up/down button (All/Favorite/Digital only/Analog only)Sets favorite channels. (p. 20)Changes the station identifier. (p. 39)Checks the signal strength if interference or freezing occurs on a digital image. (p. 39)Adjustments/Configurations (alternatives)Sets the mode to select the channel with Channel up/down button(All/Favorite/Digital only/Analog only)• Favorite: Only channels registered as FAVORITE (p. 20)Channel surf modeAllSelects the screen menu language (p. 16) LanguageAdjusts the clock (p. 17) ClockSets channels (p. 39) ANT/Cable setupSelects the terminal and label of the external equipment (p. 41)Prevents “Image retention” with Wobbling. (Automatic/Periodic)• Automatic: Shifts the display image automatically.• Periodic: Shifts the display image every (1/2/3/4) minutes according to what was set in the “Time (minutes)” menu.Pixel orbiter AutomaticSets the time for “Pixel orbiter-Periodic” setting. (1/2/3/4) Time (minutes) 4Change the brightness of the side bar (Off/Dark/Mid/Bright) (4:3 mode only)• The recommended setting is “Bright” to prevent panel “Image retention”. (p. 48) 4:3 side bars BrightPress “OK” to start horizontal “Scrolling” on the screen (p. 48) Scrolling barControls equipment connected to HDMI terminals (p. 32) (On/Off)• “Power off link”, “Power on link”, “Stand-by power save”, “Auto power stand-by” and “Default speakers” cannot be selected if “Off” is set. VIERA Link OnSets “Power on link” of HDMI connection equipment (p. 32) (Yes/No) Power on link YesSets “Power off link” of HDMI connection equipment (p. 32) (Yes/No) Power off link YesSet “Stand-by power save” of HDMI connection equipment. (p. 32) (No/Yes) Stand-by power saveNoSet “Auto power stand-by” of HDMI connection equipment. (p. 32)(No/Yes (with reminder)/Yes (no reminder)Auto power stand-byNoSelects the default speakers (p. 32) (TV/Theater) Default speakers TVTo conserve energy, the TV automatically turns off when NO SIGNAL and NO OPERATION is performedfor more than 10 minutes. (Enable/Disable)Note• Not in use when setting “Auto power on”, “On/Off Timer”, “Lock”, “SD mode” or Digital channel.• “No signal for 10 minutes was activated” will be displayed for about 10 seconds when the TV is turnedon for the first time after turning the power off by “No signal for 10 minutes”.• The on-screen display will flash 3, 2 and 1 to indicate the last three (3) remaining minutes prior to the shut-off.No signal for 10 minutesEnableTo conserve energy, the TV automatically turns off when no operation of remote or side panel keycontinues for more than 3 hours. (Enable/Disable)Note• Not in use when setting “Auto power on” or “On/Off Timer”.• “No activity for 3 hours was activated” will be displayed for about 10 seconds when the TV is turned onfor the first time after turning the power off by “No activity for 3 hours”.• The on-screen display will flash 3, 2 and 1 to indicate the last three (3) remaining minutes prior to the shut-off.No activity for 3 hoursDisableTurns TV On automatically when the cable box or a connected device is turned On (No/Yes)TV AC cord must be plugged into this device. TV comes on every time the power is restored.• The “Sleep” timer, “On / Off timer”, and “First time setup” will not function if “Auto power on” is set. (p. 42)Auto power on NoSet “Thumbnail” or “Slideshow” to play back SD cards automatically. (Slideshow/Thumbnail/Set later/Off) Play SD card automaticallySet laterDisplays TV version and software license. AboutPerforming Reset will clear all items set with Setup, such as channel settings. (p. 38) Reset to defaults(Continued)