Panasonic SOUNDSLAYER SC-GN01 User Manual

Panasonic SOUNDSLAYER SC-GN01 User Manual Manual pdf 2 page image

∫ Unit∫ Places where you use or store the product• This unit is for indoor use.• Do not use or leave where the temperature is extremely high such as in locations exposed to directsunlight or near heating devices.• Do not use or leave in locations with a lot of dust.• Do not use or leave in locations with a lot of vibration.• Do not use or leave in locations with a lot of moisture, such as bathrooms.∫ Handling• Do not drop, hit, or apply strong shocks. This may cause malfunction.• Sound may be interrupted or you may hear noise if the plug tip is dirty. If this occurs, wipe the tips ofthe plug and plug adaptor clean with a soft dry cloth.• When connected with the audio cable (supplied)– This unit is for use with stereo AV devices.– Sound is not output from the right side (R) if used with monaural devices.• If the USB cable has excess length, coil it up to an appropriate length on the USB plug side before use.Before requesting service, make the following checks. If you are in doubt about some of thecheck points, or if the remedies indicated in the chart do not solve the problem, refer to“Customer Services Directory” on the front page if you reside in the U.S.A., or refer to“CONTACT INFORMATION” on the front page if you reside in Canada.The unit does not work.• Make sure the USB cable is firmly connected to the USB port of each device or the AC adaptor(optional).• Make sure the USB port is normal. If there are other USB ports on your computer, try using oneof the other USB ports.• If the power still does not come on even after performing the above, unplug the USB cable andthen plug it in again.There is no sound.• The USB port or plug may be dirty. Wipe the USB port and plug clean with a soft dry cloth.• The sound may have been muted or turned down low on the connected device. Adjust thevolume on the connected device.• Make sure that “SC-GN01” is selected as the audio output device on the connected device.The sound is low.• Also increase the volume on the other devices as well as this unit.• You may have connected to a USB2.0 port. Connect to a USB3.0 port.There are interruptions to the sound. / Too much noise. / Poor sound quality.• Make sure the USB port is normal. If there are other USB ports on your computer, try using oneof the other USB ports.• There may be a USB hub between the unit and the computer. If there are other USB ports onyour computer, try using one of the other USB ports.• You may be trying to supply power from the USB port of a device which is the same as theinput and output of analogue audio signals or another device that is connected by some kind ofwiring. Supply power with a USB AC adaptor, etc..Cannot operate the unit.• Try unplugging the USB cable and then plugging it in again.There is no surround effect.• Make sure that “Panasonic SC-GN01 (Game)” is selected as the sound device on your PC.No output of chat audio.• Make sure that “Panasonic SC-GN01 (Chat)” is selected as audio output device on your game,chat app, or meeting app, etc.Poor sound quality for chat audio.• Turn off the noise cancelling functions in the apps you are using for chat or meetings, then try again.Low volume for chat audio.• Also increase the volume on the other devices as well as this unit.No output of analogue audio.• Check whether there is a problem with the headphone jack or analogue output terminal on thedevice you are using. Use a pair of earphones or headphones to check whether audio is beingoutput correctly, then try again.This unit is not detected when connected with the USB cable.• Try restarting the connected device.An opening sound is made while the USB cable is connected.• Due to its specifications, the connected device may temporarily stop supplying power via USB.When this occurs, this unit may turn off and then on, but it is not a malfunction.Cannot raise the output when in the mode for adjusting speaker balance or the mode foradjusting audio output.• This unit has a function that activates a control mechanism that suppresses the output whenthe volume is high. This is not a malfunction. Before making adjustments, lower the volume.∫ General∫ Amplifier section∫ Speaker section∫ Microphone section∫ Terminal section∫ Compatible equipment *4∫ Accessories*1 When the power supply capacity of the USB port on the connected device is 5 V 900 mA.Volume reduces if the power supply is 5 V 500 mA.*2 When the audio cable (supplied) is used for the connection to the headset terminal on theconnected device, also connect the USB cable to either the USB port on the connecteddevice or to a USB AC adaptor (optional). Use a USB AC adaptor (optional) with a powersupply capacity equivalent to 5 V 900 mA.*3 Audio output and microphone input operation is not guaranteed with all devices equippedwith headset terminals compatible with a 3.5 mm mini jack.*4 Before connecting with other devices, be sure to read the operating instructions for each ofthe devices.*5 For use, connect the USB plug to either the USB port on the connected device or to a USBAC adaptor (optional).*6 Operation is not guaranteed on all computers that are running the supported OSs.This is done when returning the unit to the state of purchase, such as by discarding ortransferring the unit.1 Press [VOL j] until the volume reaches the minimum level [0].• An operation tone is made when the volume reaches the minimum level [0].2 Press and hold the [SOUND] and [MUTE] buttons for about 5 seconds or more.• An operation tone is made and the unit is in the factory settings mode.• When the unit enters the factory settings mode, the operation indicator blinks once everysecond.3 Press the [MIC MUTE] button while the unit is in the factory settings mode.• The settings are each initialised, returning to the factory settings.EnglishSafety precautionsWARNING:To reduce the risk of fire, electric shock or product damage,• Do not expose this unit to rain, moisture, dripping or splashing.• Do not place objects filled with liquids, such as vases, on this unit.• Use the recommended accessories.• Do not remove covers.• Do not repair this unit by yourself. Refer servicing to qualified service personnel.This unit may receive radio interference caused by mobile telephones during use. If such interferenceoccurs, please increase separation between this unit and the mobile telephone.The symbols on this product (including the accessories) represent the following: DCTHE FOLLOWING APPLIES ONLY IN THE U.S.A.FCC Note:This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution:Any unauthorized changes or modifications to this equipment would void the user’s authority tooperate this device.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.Supplier’s Declaration of ConformityTrade Name: PanasonicModel No.: SC-GN01Responsible Party: Panasonic Corporation of North AmericaTwo Riverfront Plaza, Newark, NJ 07102-5490Support Contact: http://shop.panasonic.com/supportTHE FOLLOWING APPLIES ONLY IN CANADA.CAN ICES-003(B)/NMB-003(B)TroubleshootingSpecificationsPower supply DC 5 V, 900 mA• Power is supplied from the USB cable on the connected equipmentPower consumption Approx. 4.5 WDimensions (W k H k D) Approx. 240 mm (9 1 /2q) k 46 mm (1 13 /16q) k 209 mm (8 1 /4q)Length of USB cable Approx. 3 m (9.8 ft)Mass (Weight) Approx. 244 g (8.6 oz)Operating condition Operating temperature range:5 oC to 35 oC (41 oF to 95 oF)Operating humidity range:20 %RH to 80 %RH (no condensation)Total RMS output power(non-simultaneous drive)4 W *1(1 kHz, T.H.D., 10.0 %, 6 h, 20 kHz LPF)FTC output power 0.2 W i 0.2 W i 0.1 W i 0.1 W *1(1 kHz, T.H.D., 1.0 %, 6 h, 20 kHz LPF)Front speaker (L/R) builtin,Surround speaker (L/R)built inSpeaker units:3 cm (1 3 /16q) Cone type 4 pcsImpedance:6 hMicrophone units MEMS type 2 pcsUSB plug USB Type AAudio input/output (AUX)(for headset terminal)*2 3.5 mm mini jack CTIA compliant *3Connection with USBcablePC, PS4/PS5,Nintendo Switch (TV mode)Connection with Audiocable*5PC, PS4/PS5,Xbox One/Xbox Series S/X,Nintendo Switch (Tabletop/Handheld mode)PC compatible OS*6 Windows 10Audio cable Approx. 1.5 m (4.9 ft)Restore factory settings

/ 5

Related manuals for Panasonic SOUNDSLAYER SC-GN01