Panasonic SL-VTPR Series Instruction Manual

Panasonic SL-VTPR Series Instruction Manual Manual pdf 1 page image

SL-VTPR□Relay Output TerminalFlexible Wire-saving Link System S-LINK VINSTRUCTION MANUALMJE-SLVTPR No.0063-19VThank you very much for purchasing Panasonic products. Read this Instruc-tion Manual carefully and thoroughly for the correct and optimum use of thisproduct. Kindly keep this manual in a convenient place for quick reference.● Never use this product in a device for personnel protection.● In case of using devices for personnel protection, use products whichmeet laws and standards, such as OSHA, ANSI or IEC etc., for person-nel protection applicable in each region or country.● Before touching this product, remove any electrostatic charge that maybe present on your body. There is a danger of this product getting dam-aged due to the electrostatic charge.Please refer to the "S-LINK V User's Manual" for details of the entireS-LINK V system.PARTS NAMES AND FUNCTIONS1SL-VTPR4 SL-VTPR8123468754-core flat cable, 0.6m long875123464-core flat cable, 0.6m longDesignation Function1 Address setting switches Used for setting of the terminal address.2 Output holding functionsetting switchUsed for setting of the output holding function.ON: Hold the current output conditions (output holding).OFF: Will not hold the current output conditions (output OFF).3 Power indicator (Green) This indicator will light when the power is supplied.4 Transmission indicator(Green)This indicator will blink when the synchronizationsignal is sent from the S-LINK V controller.5 Operation indicator(Orange) Lights when each output relay is turned ON.6 Relay remover key Use this key to remove the output relays.7 Output relay PA-N relay APAN3124 manufactured by PanasonicCo., Ltd. (Note)8 Terminal block Used for connection of output devices.Note: You can replace the output relays.For a detailed description, refer to “ RELAY REPLACEMENT.”MOUNTING2Mounting method1. Push the DIN rail stopper inside.2. Fit the tab on the opposite side of theDIN rail stopper into the 35mm widthDIN rail.3. Press down the tab on the other sideagainst the 35mm width DIN rail to fit it.DIN rail stopper35mm width DIN rail132Removing method1. Insert a flathead screwdriver to thegroove on the DIN rail stopper and pullout the stopper.2. Push the product to the other side ofthe DIN rail stopper.3. While maintaining the condition in theprocedure 2, and lift up the product toremove it.Flathead screwdriverDIN rail stopperNote: Take care that if the product is lifted with the stopper remained inside, the tabs crack.OUTPUT CIRCUIT DIAGRAM (per channel)3S-LINK V system side Internal circuit Output device sideMain circuitOutput relay+24VDG0VOutput SL-VTPR4: Output 0 to 3SL-VTPR8: Output 0 to 7● Terminal arrangement diagramSL-VTPR4 SL-VTPR8Upper sideLower sideOutput 0Output 2Output 1Output 3TerminalNo.DIN rail stopperUpper sideLower sideOutput 0Output 5Output 3Output 7Output 6Output 4Output 2Output 8TerminalNo.DIN rail stopperOutputOutput 0Output 1Output 2Output 3TerminalNo.5 6 7 81 2 3 4OutputOutput 0Output 1Output 2Output 3Output 4Output 5Output 6Output 7TerminalNo.9 10 11 12 13 14 15 161 2 3 4 5 6 7 8CoverM4 pan head screwPlease arrangeseparately● In case of mounting with screws, useM4 pan-head screws and the tighten-ing torque should be 0.8N·m or less.W59.2mm Model No. WSL-VTPR4 47.5mmSL-VTPR8 78mmDimensions for mounting holesSL-VTPR8 + AQZ202D4.003.002.001.000-20 0 20 40 60Ambienttemperature (°C)Load current (A) No. of output-ON relay pts.: 1 or 2No. of output-ON relay pts.: 7 or 8No. of output-ON relay pts.: 3 or 4No. of output-ON relay pts.: 5 or 6Ambienttemperature (°C)SL-VTPR8 + AQZ204D0.400.300.200.100-20 0 20 40 60Load current (A)No. of output-ON relay pts.: 7 or 8No. of output-ON relay pts.: 1 or 2No. of output-ON relay pts.: 3 or 4No. of output-ON relay pts.: 5 or 6Ambienttemperature (°C)SL-VTPR8 + AQZ205D2.001.501.000.500-20 0 20 40 60Load current (A)No. of output-ON relay pts.: 7 or 8No. of output-ON relay pts.: 1 or 2No. of output-ON relay pts.: 3 or 4No. of output-ON relay pts.: 5 or 6Ambienttemperature (°C)SL-VTPR8 + AQZ207D0.800.600.400.200-20 0 20 40 60Load current (A)No. of output-ON relay pts.: 7 or 8No. of output-ON relay pts.: 1 or 2No. of output-ON relay pts.: 3 or 4No. of output-ON relay pts.: 5 or 6● In case of using PA-N relay (APAN3124), use this product in the ambienttemperature range of -10 to +55° and with 3A output current.● In case of using PhotoMOS relay (AQZ20□D), the output current isrestricted depending on ambient temperature and the number of Photo-MOS relay ON points.Ambient temperature and number of PhotoMOS relay ON points -Load current characteristics● The upper limit value of the load current depends on the ambient tem-perature and the number of PhotoMOS relay ON points.

/ 2

Related manuals for Panasonic SL-VTPR Series