Panasonic SG-PK-M Series Quick Instruction Manual

Panasonic SG-PK-M Series Quick Instruction Manual Manual pdf 1 page image

QUICK INSTRUCTION MANUALNon-Contact Safety Door SwitchMaintenance Actuator SG-PK-MƑ SeriesCMJE-SGPKM No.0077-18VThank you very much for purchasing Panasonic products. Read this Instruction Man-ual carefully and thoroughly for the correct and optimum use of this product. Kindlykeep this manual in a convenient place for quick reference.7KLVGRFXPHQWEULHÀ\VXPPDUL]HVLQVWDOODWLRQDQGRSHUDWLRQRIWKHSURGXFWWhen using the product, refer to the SG-P Series Instruction Manual in addition tothis manual.The SG-P Series Instruction Manual can be downloaded from our website (https://panasonic.net/id/pidsx/global).Use this product together with the Non-contact Safety Door Switch SG-P Series.When using the SG-P Series, refer to the SG-P Series Quick Instruction Manualand SG-P Series Instruction Manual.1 SAFETY CAUTIONS Always observeThis section explains important rules that must be observed to prevent personalinjury and property damage.Ŷ 7KHKD]DUGVWKDWPD\RFFXULIWKHSURGXFWLVXVHGLQFRUUHFWO\DUHGHVFULEHGDQGFODVVL¿HGE\OHYHORIKDUPWARNING Risk of death or serious injury.CAUTION Risk of minor injury or property damage.WARNINGƔ Machine designer, installer, employer and operator• The machine designer, installer, employer and operator are solely responsibleto ensure that all applicable legal requirements relating to the installation andWKHXVHRIWKLVGHYLFHLQDQ\DSSOLFDWLRQDUHVDWLV¿HGDQGDOOLQVWUXFWLRQVIRULQ-stallation and maintenance contained in the instruction manual are followed.• Whether this device functions as intended to and systems including this de-vice comply with safety regulations depends on the appropriateness of the ap-plication, installation, maintenance and operation. The machine designer, in-staller, employer and operator are solely responsible for these items.Ɣ Engineer• The engineer would be a person who is appropriately educated, has wide-spread knowledge and experience, and can solve various problems whichmay arise during work, such as a machine designer, installer or employer etc.Ɣ Operator• The operator should read this instruction manual thoroughly, understand itscontents, and perform operations following the procedures described in thismanual for the correct operation of this device.• In case this device does not perform properly, the operator should report this tothe person in charge and stop the machine operation immediately. The machinePXVWQRWEHRSHUDWHGXQWLOFRUUHFWSHUIRUPDQFHRIWKLVGHYLFHKDVEHHQFRQ¿UPHGƔ Environment• This device is suitable for indoor use only.• Do not use this device in an explosion-proof area.• Do not install this device in the following places:1) Areas with high humidity where condensation is likely to occur2) Areas exposed to corrosive or explosive gases3) Areas exposed to contact with water4) Areas exposed to too much steam or dust• Do not use this device near equipment that emits strong electromagneticwaves.Ɣ Machine in which this device is installed• Do not install this device with a machine whose operation cannot be stopped im-mediately in the middle of an operation cycle by an emergency stop equipment.Ɣ Maintenance• When replacement parts are required, always use only genuine supplied re-placement parts. Using substitute parts from another manufacturer may causethe device not to detect objects, resulting in death or serious injury.• The periodical inspection of this device must be performed by an engineerhaving the special knowledge.• Clean this device with a clean cloth. Do not use any volatile chemicals.Ɣ Other precautions• 1HYHUPRGLI\WKLVGHYLFH0RGL¿FDWLRQPD\FDXVHWKHGHYLFHQRWWRGHWHFWRE-jects, resulting in death or serious injury.CAUTION6SHFL¿FDWLRQVƔ This product has been developed / produced for industrial use only.Ɣ 'RQRWXVHWKLVSURGXFWRXWVLGHWKHUDQJHRIWKHVSHFL¿FDWLRQV5LVNRIDQDFFLGHQWand product damage. There is also a risk of a noticeable reduction of service life.Ɣ Use this device by installing suitable protection equipment as a countermeasurefor failure, damage, or malfunction of this device.Ɣ Before using this device, check whether the device performs properly with theIXQFWLRQVDQGFDSDELOLWLHVDVSHUWKHGHVLJQVSHFL¿FDWLRQVƔ Note that this device may be damaged if it is subject to a strong shock (if it isGURSSHGRQWRWKHÀRRUIRUH[DPSOH Ɣ 'RQRWXVHWKHGHYLFHQHDUDQDSSDUDWXVWKDWJHQHUDWHVPDJQHWLF¿HOGV2WKHU-ZLVHWKHRSHUDWLQJGLVWDQFHPD\EHDႇHFWHGƔ Do not apply an excessive shock to the safety switch when opening or closingthe door.Ɣ Use of this device under the following conditions or environments is not presup-posed. Please consult us if there is no other choice but to use this device in suchan environment.1) Operating this device under conditions or environments not described in thismanual. 8VLQJWKLVGHYLFHLQWKHIROORZLQJ¿HOGVQXFOHDUSRZHUFRQWUROUDLOURDGDLU-craft, auto mobiles, combustion facilities, medical systems, aerospace devel-opment, etc.Ɣ When the apparatus that uses this device is to be used for enforcing protection of aperson from any danger occurring around the area where machines are operated,the user should satisfy the regulations established by national or regional securitycommittees (Occupational Safety and Health Administration: OSHA, the European&RPPLWWHHIRU6WDQGDUGL]DWLRQHWF &RQWDFWWKHUHODWLYHRUJDQL]DWLRQ V IRUGHWDLOVOther precautionsƔ Never attempt to disassemble, repair, or modify the product.Ɣ When this device becomes inoperable or unnecessary, dispose of the productproperly as industrial waste by abiding by the applicable law in the country.2 CONTENTS OF PACKAGEActuator body: 1 unitQuick Instruction Manual (English / Japanese, Chinese): 1 volume each3 PRODUCT CONFIGURATIONInstalling this product directly on the switch body enables a distinction from an abnor-mal door open state.This product is available in two types: one is a collective maintenance type (SG-PK-M1) and the other is an individual maintenance type [SG-PK-M2 (Note)].Note: Multiple units of the individual maintenance type (SG-PK-M2) can be installed at the same time. Switch bodyThis productSwitch bodyThis productƔ The collective maintenance type (SG-PK-M1) can be installed only on the switchbody (standard).Ɣ The individual maintenance type (SG-PK-M2) can be installed on either theswitch body (standard) or switch body (sub).Ɣ When using this product, it is not possible to use the redundant input monitoring(dual channel monitoring) with the SG-P Series OSSD1 and OSSD2 using thesafety controllers, etc.Ɣ When using the maintenance actuator, make sure that the normal actuator is notdetected at the same time.Ɣ Use the product with a system that distinguishes between the normal mode andmaintenance mode.4 NAME OF PARTSFor details of the switch body, refer to the SG-P Series Quick Instruction Manualand SG-P Series Instruction Manual.Key ring mounting holeModel No. printingRelease leverFixing claw(Bottom side)Fixing claw(Top side)Actuator detection surface5 MOUNTING AND REMOVALThe procedures to mount this product on the switch body or to remove it from theswitch body are as follows.Visible typeƔ Mounting procedure1. )LWWKH¿[LQJFODZ ERWWRPVLGH IURPWKHIURQWVLGHRIWKHVZLWFKERG\DORQJWKHroot of the cable.12. 3XVKLQWKH¿[LQJFODZ WRSVLGH WRVHFXUHLWRQWKHVZLWFKERG\2Ɣ Removal procedureWhen removing this product from the switch body, push in the release lever locatedULJKWEHORZWKH¿[LQJFODZ WRSVLGH WROLIWWKH¿[LQJFODZ:KLOHWKH¿[LQJFODZLVOLIWHGSXOORXWWKHSURGXFWWRUHPRYHLWIURPWKHVZLWFKERG\Pull outPush inNote: Do not hold and pull any part of the product other than the release lever when removing it from the switch body.Doing so will cause a failure or damage.

/ 2

Related manuals for Panasonic SG-PK-M Series