|
HOW TO USE “SETUP MENU” (cont'd) SETTING>COLOR SYSTEM :AUTORUSH DELAY TIME :STD.HOUR METER X100h :000EXIT: MENU ADJUST:- + SELECT: SUB ADJ.>CONTRAST :00BRIGHT :00CHROMA :00PHASE :00NTSC SETUP :00COMPO.LEVEL :SMPTEsub menuresetEXIT: MENU ADJUST:- + SELECT: ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS1. FUNCTION SETTINGSelects the colour system anddisplays the monitor’s power-up time or the total usage time.Press the button to displaythe setting menu illustrated onthe right.Item : COLOR SYSTEMSettings : AUTO/NTSC/PALFunction : Selects the colour system when using the videoinput card.AUTO : Change NTSC and PAL automatically.NTSC : Keeps the colour system NTSC.PAL : Keeps the colour system PAL.NOTE : Normally select AUTO. However, if the input signal isunstable, select NTSC or PAL.Item : RUSH DELAY TIMESettings : STD./SLOWFunction : Sets the time when the power supply to themonitor’s circuits (excluding the micro computers)starts after the power switch is pressed.STD. : The power supply starts approx.1 second after the power switch ispressed.SLOW : The power supply starts approx.3.2 seconds after the power switch ispressed.NOTE : When turning on many multi-format monitorssimultaneously, it is recommended to use SLOW tocontrol rush current.Item : HOUR METER X100hNumberrange : 000 ~ 655Function : Displays the total usage time of the monitor inhundred-hour units.● When the timer passes 655, it returns to 000.● The timer does not count the usage time under one hour.2. PICTURE SUB ADJ.Performs approximateadjustments using the controlknobs on the front panel. Pressthe button to display thesetting menu illustrated on theright.NOTE : When the RGB signalis input, onlyCONTRAST andBRIGHT are displayed. When the PAL signal isinput, only CONTRAST, BRIGHT and CHROMA aredisplayed.Item : CONTRASTAdjustmentrange : –20 ~ 00 ~ +20Function : For approximate adjustment of the picturecontrast. Before adjustment, set the CONTRASTknob on the front panel to 0.Item : BRIGHTAdjustmentrange : –20 ~ 00 ~ +20Function : For approximate adjustment of the picturebrightness. Before adjustment, set the BRIGHTknob on the front panel to 0.Item : CHROMAAdjustmentrange : –20 ~ 00 ~ +20Function : For approximate adjustment of the colourdensity. Before adjustment, set the CHROMAknob on the front panel to 0.Item : PHASEAdjustmentrange : –20 ~ 00 ~ +20Function : For approximate adjustment of the picture hue.Before adjustment, set the PHASE knob on thefront panel to 0.Item : NTSC SETUPSettings : 00/7.5Function : Sets the level of the input NTSC signal.00 : Compliant with 0% set-up signal.7.5 : Compliant with 7.5% set-up signal.NOTE : NTSC SETUP is displayed only when the video inputcard is installed and an NTSC signal is input.Item : COMPO. LEVELSettings : SMPTE/B75/B00Function : Sets the level of the input component signal.SMPTE : Compliant with M2VTR signals.B75 : Compliant with Betacam 7.5% set-upsignal.B00 : Compliant with Betacam 0% set-upsignal.NOTE : COMPO. LEVEL is displayed only when a 480/60i,480/60p, 576/50i or 576/50p signal is input.Item : sub menuAdjustment range/Settings : Same as CONTRAST, BRIGHT, CHROMA,PHASE and COMPO. LEVEL/NTSC SETUP.Function : Performs CONTRAST, BRIGHT, CHROMA,PHASE or COMPO. LEVEL/NTSC SETUPsettings in a single-line display. The sub menudisplay varies depending on the selected item.Item : resetFunction : Sets the CONTRAST, BRIGHT, CHROMA,PHASE and COMPO. LEVEL/NTSC SETUPvalues to factory-preset ones.14
|
