Panasonic AW-RP605AN Operating Instructions Manual

Panasonic AW-RP605AN Operating Instructions Manual Manual pdf 3 page image

3When the pan/tilt head system is connected (or changed)and its power is turned on for the first time, the connectedcameras will be initialized. Upon completion of theinitialization, adjust or set the following items. After the itemsare adjusted or set, proceed to the section entitled “Settingthe travel range (limiters) of the pan/tilt head”.Once the adjustments are made, there is no need for anyre-adjustments unless changes are made to the pan/tilthead, camera or lens. (The items to the re-set or re-adjusteddiffer depending on the unit which is changed.)U Setting the camera modelThese steps must be taken without fail when using theAW-PH300, AW-PH300A or AW-PH600 pan/tilt head.1. Press the MENU button, and turn the menu settingcontrol (main) to display the CONTROLLER SETTINGitem on the top line of the LCD panel.2. Press the OK button. The following item appears on theLCD panel.3. Turn the menu setting control (main) to display thefollowing item on the LCD panel.4. Turn the menu setting control (L) to select the camerasconnected, and turn the menu setting control (R) toselect the camera models connected.5. After all the camera models connected are set, press theMENU button to restore the original display to the LCDpanel.❈ These settings need not be performed when connecting apan/tilt head other than the AW-PH300, AW-PH300A orAW-PH600. Either each camera model will beautomatically identified or the pan/tilt head will not allow aconvertible camera to be connected.U Adjusting the minimum start speed of the pan/tilt headWhen the pan/tilt head is to be operated manually using thejoystick, its minimum start speed is automatically adjusted toensure that the pan/tilt head will start moving smoothly inresponse to the angle to which the pan/tilt lever is tilted.(This will reduce the amount of play in the pan/tilt lever.)1. Press the MENU button, and turn the menu settingcontrol (main) to display the P/T SETTING item on thetop line of the LCD panel.2. Press the OK button. The following item appears on theLCD panel.3. Turn the menu setting control (main) to display thePAN/TILT MIN SPD Set item on the top line of the LCDpanel.4. When the OK button is pressed, the OK button lampstarts flashing, the speed is automatically adjusted in thesequence of right, up, left and down. When all theadjustments are completed, the display status shown instep 3 above is restored.5. If an adjustment could not be made during the adjustmentprocess, PAN/TILT ADJ Error appears on the bottom lineof the LCD panel, and the operation is shut down.6. Now re-balance the camera which is installed on thepan/tilt head. When the OK button is then pressed, thedisplay status shown in step 3 above is restored, and theautomatic adjustments are commenced again.7. After all the adjustments are completed, press the MENUbutton to restore the original display to the LCD panel.❈ When the menu is set to these adjustment items, nooperations can be initiated by the pan/tilt lever. Uponcompletion of the automatic adjustments, be absolutelysure to change the menu to another item.PPAANN//TTIILLTT MMIINN SSPPDD SSeettAADDJJ SSttaarrtt PPuusshh OOKK KKeeyyPPAANN//TTIILLTT MMIINN SSPPDD SSeettPPAANN//TTIILLTT AADDJJ EErrrroorrPPAANN//TTIILLTT MMIINN SSPPDD SSeettAADDJJ SSttaarrtt PPuusshh OOKK KKeeyyPPAANN DDIIRREECCTTIIOONNNNOORRMMAALLPP//TT SSEETTTTIINNGGn OOKK KKeeyyCCaammeerraa MMooddeell SSeelleeccttCCAAMM11 NNoo CCaammeerraaSSIIGGNNAALL SSEELLEECCTTCC..VVIIDDEEOO n CC..VVIIDDEEOOCCOONNTTRROOLLLLEERR SSEETTTTIINNGGn OOKK KKeeyyOperationWhen using component signalsWhen component signals are to be used, either aconvertible camera requiring the installation of an optionalRGB card (AW-PB302) or a convertible camera (such as theAW-E650), which does not require the installation of such acard, is available.For details on the camera's output signals, refer to theoperating instructions provided with the camera used.Connections