Menu
KiSS MC-230 Owner's Manual
   |
SAFETY CAUTIONIMPORTANT NOTICEOPERATING INSTRUCTIONS1. Use this appliance for its intended purpose. Use only on clean, dry hair.2. Close supervision is necessary when this appliance is by or near children.3. Use only with accessories included in the package, (or those recommended bythe manufacturer).4. Avoid contact with the eye area. Do not use on open wounds; damaged orsensitive skin.5. Except when charging, always unplug from the electrical socket after use.6. Keep away from water, liquids or any detergent agents.7.To avoid cord damage, do not pull, twist or wrap the cord tightly.8. Charging should be done indoors and in a cool dry place.9. The charger adaptor must be kept dry at all times.1. The blade, main unit, power cord or attachment comb is damaged2. The clipper or the adapter is dropped into water or liquid.3. The clipper is switched off, but the charging indicator does not light up whenplugged into the power source.*The clipper and accessories must be checked regularly for damage. If damage isdetected, do not put the device into operation.1. The blade must be lubricated before and after each use. This will maintain it ingood condition and will extend its service life.2. Non - stop usage for hours may cause overheating of blades, reducing the cuttingperformance and shortening their life. Should the blades overheat, switch the unitoff for a few minutes to let it cool down and lubricate the blades.3. Hair must be clean and dry before cutting. Foreign matter hidden in the hair maydamage the blade edge.4. Hair may gather inside the blade housing during use. Too much stored hair willreduce the oscillating ability of the blades and cause malfunctioning.Clean up hair in the blade housing before and after each use.5. Avoid impact of the blade with hard objects as this may cause damage to theblade teeth.1. Do not overcharge. It takes (an estimate of)1 hour to charge your trimmer.Charging more than 36 hours may shorten the life of the battery.2. The life of the battery will be shortened if the trimmer remains uncharged for longperiods. Charge unused clippers every 3 months to activate and maintain thebattery.3. It is normal for the adapter and the internal parts to become warm when charging.1. Use or store the trimmer only at room temperature. Avoid direct sunlight,moisture or heated surfaces. Operating range 0 - 40 ℃.2. Do not attempt to unscrew any part of the trimmer.1. Icon “ ” can be seen on LCD screen to remind you of charging.2. Connect the charging cord to the charging slot at one end of clipper.Should the following situations occur, unplug and switch off immediately,and send for examination or repair.Always switch off before removing, replacing and cleaning the blade.Recharging time: 1 hourCordless operation time: 1.5 hours (5000RPM)The “ ” icon will twinkled when the available time is only 5 mins left, to remindyou charging or connecting wires in time.This trimmer can be operated electrically by plugging it into the power source(when the battery is not fully charged).1. Turn power switch off.2. Connect the adapter to the wall socket.3. Connect the DC plug to the clipper.4. Check if the charging indicator is lit.5. Switch on to operate.* Except for the purpose of charging, always switch off and unplug the adapterfrom the wall socket after use.* Do not frequently use the clipper plugged in without having recharged thebattery, as this may reduce the life of the battery.* Charge at room temperature between 5℃ and 35℃.1. Remove the blade set from the blade housing by pressing the top cutting headwith your thumb.2. Brush off the residual collected hair thoroughly from between the teeth and theblade housing.3. Move the oscillating bracket with your thumb to separate stored hair from theblades. Brush off the hair between the blades. Make sure hair is not trappedbetween the blades.Lubricate both friction surfaces of the front cutting teeth and the hind supporting areas.1. Hind supporting areas: push the oscillating part to one side: lubricate the visiblefriction surface on the other side. Drop a small amount of oil on both sides.2. Front cutting teeth: Drop a small amount of oil on the blade teeth and spread evenly.Slightly move the oscillating part to spread the oil between the blades.1. To replace the blade set, put the bottom of the blade set clip into the blade setMount on the blade housing.2. Push until it snaps into place.1. Switch off and unplug the trimmer before cleaning2. Wipe with a soft damp cloth.3. Allow it to air dry before use.Keep Away from Water and LiquidsMAINTENANCERemoving and Cleaning the BladeLubricating the BladeReplace the BladeCleaning the Main Body and AccessoriesCautionBattery Condition IndicatorCord OperationBladeBatteryOthersChanging2 33. Confirm that the switch is off and insert the plug.4. Charging indicator “low” & “ ”can be seen on LCD.5. It will automatically stop after a full charge; both icons “low” & “high” can beseen on LCD.6. A full charging takes about 1 hour. The battery will reach optimum performanceafter three charges. |
Related manuals for KiSS MC-230
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved