Haier LY26R3A Instruction Manual

Also see for LT26K3:

Language

English

Contents

English1

Français13

Deutsch25

Italiano37

Dutch49

Haier LY26R3A Instruction Manual Manual pdf 12 page image

PLAYING A JPEG CD1.Insert a JPEG CD in the same way as you would a DVD or Audio CD, with the labelfacing away from you.2.The CD will load and a menu of the disc's contents will appear on screen.3.Use the and buttons to highlight the folder and picture you wish to view and pressPLAY/PAUSE. Each image on the disc will show consecutively, like a slide show.4.Press PLAY/PAUSE during the slide show to pause on one image.5.Press the or button to skip to the next image or return to the previous one.PLAYING AN AUDIO CD1.Insert a CD in the same way as you would a DVD, with the label facing away from you.2.The CD will load and a menu of the disc's contents will appear on screen.3.Use the and buttons to highlight the track you wish to play and press PLAY/PAUSE,or just press PLAY/PAUSE to listen to the whole CD from the beginning.You can stop, pause, fast forward or fast rewind a CD in the same way as a DVD.You can also use the REPEAT button to repeat a track, folder album or the contents ofthe whole disc. Press repeatedly to select what you would like to repeat. You can alsouse the A-B function to repeat a certain section of a track or CD.TROUBLESHOOTINGTo assist in location of possible faults use the help guide below:Note:1.If the fault can not be repaired using the above guide consult with your local authorizedservice centre.2.The TV set must only be repaired by a qualified registered service person. Never attempt toremove the back cover as the TV set has dangerous voltages in side that may cause afatally or fire.No picture, no sound Verify if the television is properly plugged in.Verify if the television has a proper supplied power source.Verify if electricity is available.Blank screen Verify if correct signals are input.Operate the remote to change signal input to correct input.Restart the television if power supply is interrupted.No soundPress MUTE button and verify if Mute mode is set.Switch to other channel and verify if the same problemhappens.Press VOL+ button to see if the problem can be solved.Poor sound Verify if sound system is correct. Refer to user's manualfor adjustment.No picture in somechannelVerify if correct channel is selected.Adjust the antenna.No color for some channelprogram (black and white)Verify if the same problem exists in other channels.Check out of picture and sound systems.Refer to relative instructions in the Manual for coloradjustment.Spots with some orall picturesVerify if the antenna is correctly connected.Verify if the antenna is in good condition.Make fine adjustment of channel.Television out of controlDisconnect the television from power supply and 10seconds later, connect the television to the power supply.If the problem still exists, contact authorized after-salesservice for technical assistance.SCREEN SECTIONType A-si TFT active matrixViewable angle 160(H) 150 (V) (S626/S626D)176 (H) 176 (V) (S632F/S632D /S642F)Colour system PAL, SECAM, NTSC (AV)TV/VIDEO SECTIONSound system BG, DK, I, LVideo input SCART, S-VIDEO, YPb/Pr, YCb/Cr, AV,VGA,HDMI,USBGENERAL SECTIONDTV Y/Pb/Pr Composite: 480i/p, 576i, 720p, 1080i, 1080pPower See rating platePower consumption See rating plateDimensions (W x D x H) cm63.3 x 20.0 x 49.7 (including base) ( )63.3 x 20.0 x 49.7 (including base) ( )79.8 x 23.0 x 57.5 (including base) ( )79.8 x 23.0 x 57.5 (including base) ( )102.2 x 28.9 x 70.4 (including base) ( )66.2 x 20.0 x 50.0 (including base) ( )66.2 x 20.0 x 50.0 (including base) ( )79.6 x 23.0 x 59.0 (including base) ( )79.6 x 23.0 x 59.0 (including base) ( )102.0 x 29.0 x 72.4 (including base) ( )Environment conditions Working temperature: +5 C - +35 CWorking humidity: 20% - 80%Storage temperature: -15 C - +45 CStorage humidity: 5% - 90%Accessory User manualRemote controlBase cover (Only for S642F )Battery (x2)The part specifications of this TV set provided here are for reference only.Differences may occur as product technology is updated.Design and specifications are subject to change without notice.LT26K3LY26K3LTF32K3LY32K3LTF42K3LT26R3LY26R3LTF32R3LY32R3LTF42R3Specification

/ 60

Questions and answers

Need help?

Ask question about this manual

Frequently asked questions

To prevent fire hazards, ensure the product is tightly fixed to avoid drops, do not place it under direct sunlight or near heat sources, keep it away from water or oil, and do not use damaged electric plugs. Additionally, avoid connecting excessive sockets in parallel or sharing the same socket with multiple plugs.

During a thunderstorm, especially a rainstorm, unplug the power supply and antenna of the product to avoid electric shocks or fire hazards.

Ensure that you are aiming the remote control towards the remote sensor on the TV. If it still does not work, check the batteries in the remote control.

To install the batteries in the remote control, place the remote control face down, open the cover of the battery compartment, install two AAA 1.5V batteries ensuring the + and - symbols match the marks on the remote, and then close the cover of the battery compartment.

To change the sound mode, press the MENU button, navigate to the Sound menu, select Mode, and use the button to choose between Standard, Music, Theater, or User. You can also quickly select the desired mode using the S.MODE button on the remote control.

To set the clock, press the MENU button, use the navigation button to select the Time menu, and press the enter button. Then, select the Clock item and press the enter button. Use the navigation button to select hour or minute, and the adjustment button to set the value.

To activate the sleep timer, press the MENU button, use the navigation button to select the Time menu, and press the enter button. Then, select the Sleep item and press the enter button. Use the navigation button to select the desired time duration (Off, 5Min, 10Min, 15Min, 30Min, 45Min, 60Min, 90Min, 120Min, 180Min, 240Min) and press the MENU button to save and exit.

To turn off the sound, press the MUTE button on the remote control. The word 'Mute' will appear at the bottom of the screen, and the sound will be turned off. To turn the sound back on, press the MUTE button again or the V+ button.

If your USB device is not being recognized, ensure that it supports the Mass Storage Protocol and has a FAT32 file system. If the file system is not supported, format the USB device to FAT32. Additionally, make sure the USB device is in conformity with USB2.0 full speed Interface Standard for smooth playback.

To play a movie from a USB device, first enter the USB main interface. Press the appropriate button to select 'Movie' and then press OK to confirm and enter the movie file list. Use the directional buttons and the OK button to select the movie you want to play, and then press the PLAY/PAUSE button to start the movie. You can use the PREV/NEXT buttons to select the last or next movie, and the STOP button to stop the movie. To exit playing, press the BACK button repeatedly.

Related manuals for Haier LT26K3