Gecko in.ye-5 Quick Start Card

Also see for in.ye-5: Tech book

Gecko in.ye-5 Quick Start Card Manual pdf 2 page image

Press and hold the Program keyfor 20 seconds until you accessthe breaker setting menu.The values displayed by thesystem correspond to 80% of themaximum amperage capacity ofthe GFCI.5- Select breakerBreaker setting for GFCI used.GFCI b60 A 48 A50 A 40 A40 A 32 A30 A 24 A20 A 16 A15 A 12 APress the Program key to setbreaker rating.3- Select spa configurationInformation between ( ) indicates which AMP connector to use. SeeStep 1 for connector position.Config. # Pump 1 Pump 2 Pump 3 Pump 4 Pump 5 Blower Circ. Pump (CP) Ozone1 Filter Cycle (Daily) Heater Pump1 2 sp (A3) (A1) 2 x 2 hours with P1L Pump 12 2 sp (A3) (A1) (A4) 2 x 6 hours with CP CP3 2 sp (A3) 1 sp (A2) (A1) 2 x 2 hours with P1L Pump 14 2 sp (A3) 1 sp (A2) (A1) (A4) 2 x 6 hours with CP CP5 2 sp (A3) (A4) (A1) 2 x 2 hours with P1L Pump 16 2 sp (A3) (A4) (A1) (A2) 2 x 6 hours with CP CP7 2 sp (A3) 1 sp (A2) (A4) (A1) 2 x 2 hours with P1L Pump 18 2 sp (A3) 1 sp (A2) (A4) (A1) 2 x 6 hours with CP CP9 2 sp (A3) 2 sp (A2) (A1) 2 x 2 hours with P1L Pump 110 2 sp (A3) 2 sp (A2) (A1) 2 x 6 hours with CP CP11 2 sp (A3) 2 sp (A2) (A1) 2 x 2 hours with P1L Pump 112 2 sp (A3) 2 sp (A2) (A1) (A0)2 2 purges , CP always on CP13 2 sp (A3) 1 sp (A2) 1sp (A4) (A1) 2 x 2 hours with P1L Pump 114 2 sp (A3) 1 sp (A2) 1sp (A4) (A1) 2 x 6 hours with CP CP15 2 sp (A3) 1 sp (A2) 1sp (A4) (A1) 2 x 2 hours with P1L Pump 116 2 sp (A3) 1 sp (A2) 1sp (A4) (A1) (A0)2 2 purges , CP always on CP17 2 sp (A3) 2 sp (A2) 1sp (A1) 2 x 2 hours with P1L Pump 118 1 sp (A3) (A1) (A4) 2 x 6 hours with CP CP19 1 sp (A3) 1 sp (A2) (A1) (A4) 2 x 6 hours with CP CP20 1 sp (A3) 1 sp (A2) 1 sp (A4) (A1) (P43 tab)3 2 x 6 hours with CP CP21 1 sp (A3) 1 sp (A2) 1 sp (A4) 1 sp (A1) (A0)2 (P43 tab)3 2 purges, CP always on CP22 1 sp (A3) 1 sp (A2) 1 sp (A4) 1 sp (A1) 1 sp (P43 tab)3 (A0)2 2 purges, CP always on CPSwim Spa51 (Master) 1 sp (A3) 1 sp (A2) (A4) (A1) 2 x 6 hours with CP CP51 (Slave) 1 sp (A3) 1 sp (A2) (A4)52 (Master) 2 sp (A3) 1 sp (A2) (A1) 2 x 2 hours with P1L Pump 152 (Slave) 1 sp (A3) 1 sp (A2) (A4)53 (Master) 1 sp (A3) 1 sp (A2) (A4) (A1) 2 x 6 hours with CP CP53 (Slave) 1 sp (A3) 1 sp (A2) 1 sp (A1) (A4)54 (Master) 2 sp (A3) 1 sp (A2) (A1) 2 x 2 hours with P1L Pump 154 (Slave) 1 sp (A3) 1 sp (A2) 1 sp (A1) (A4)Use the Up/Down key to selectthe breaker value. The value canbe modified from 10 to 48 A.At first startup the keypad displaywill show L 1 or LL 1.4- Enter selectionNote: To re-enter the low levelselection menu, hold thePump 1 key for 30 seconds.Note: If the keypad in use doesnot have the Program key usethe Filter or Light key instead.Note: If the keypad in use doesnot have the Program key usethe Filter or Light key instead.Use the Up/Down key to choosethe new low level configurationnumber (consult the chart above).Press the Program key to confirmthe selection.Default breaker value is 48 A.Power management will makesure never to exceed this rating.Software #200, rev. 0039919-101192-DRev. 02-2014For complete TechBook or more information, see our website: www.geckoalliance.com© Groupe Gecko Alliance Inc., 2014All trademarks or registered trademarksare the property of their respective owners.Printed in CanadaNote 1: When the Ozonator is not controlled by a relay, it can be tied to Pump 1 Low speed or Circ. Pump using cable AMP 9920-401369.Note 2: Circ. pump is connected to a Direct fused outlet. Pump will always be on and may overheat if oversized pump is used.Note 3: This accessory does not have its own AMP connector. Rewire A0 if not used or order extra AMP connector 9920-401346 (Black wire to P43 tab on the board,Green to any G tabs and white to any N tabs for 120 V accessory or any L2 tabs for 240 V.32198

/ 2

Related manuals for Gecko in.ye-5