Fanimation KLINCH FPS7679 Series Manual

Fanimation KLINCH FPS7679 Series Manual Manual pdf 2 page image

Important Safety InstructionsWARNING: To avoid fire, shock and serious personal injury, follow these instructions.Additional Safety Instructions1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent powerfrom being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device,such as a tag, to the service panel.3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan beforeservicing.4. Do not insert anything into the fan blades while the fan is operating.5. Do not operate reversing switch until fan blades have come to a complete stop.6. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervisedto ensure that they do not play with the appliance.1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70) and Local Codes. The ceiling fanmust be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensedelectrician.3. The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. See page 5 of owner’s manual forsupport requirements. Consult a qualified electrician if in doubt.4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electricalknowledge or experience, have your fan installed by licensed electrician.6. Suitable for use with solid-state speed controls.7. This fan is to be used in damp locations.8. Use only with light kits marked suitable for use in damp locations.9. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a groundedconductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be connected to anungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then it should be connected toan equipment grounding conductor.WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE ISOLATINGWALL CONTROL/SWITCH.WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically foruse with this product. Using parts and/or accessories not designated for use with this product could result in personal injuryor property damage.WARNING: To reduce the risk of personal injury, do not bend the blade when installing the fan blades, balancing the blades, or cleaningthe fan. Do not insert foreign objects in between rotating fan blades.WARNING: Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch. Doing so could result in damage to theceiling fan’s remote control unit.WARNING: Mount to an outlet box marked acceptable for fan support of 15.9 kg (35 lbs) or Less.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation. Please note that changes or modifications not expressly approved by theparty responsible for compliance could void the user's authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and the receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Note: For a Class A digital device, statements of 15. 105(a) must be included when appropriate for the device in question.