Baileigh Industrial BHVBS-712B Operating Instructions And Parts Manual

Baileigh Industrial BHVBS-712B Operating Instructions And Parts Manual Manual pdf 2 page image

1.0 IMPORTANT SAFETYINSTRUCTIONSRead and understand the entire instructionmanual before operating machine.This band saw is designed and intended for useby properly trained and experienced personnelonly. If you are not familiar with the proper andsafe operation of a band saw, do not use untilproper training and knowledge have beenobtained.WARNING – To reduce risk of injury:a. Wear eye protection.b. Do not remove jammed cut off pieces untilblade has stopped.c. Maintain proper adjustment of bladetension, blade guides, and thrust bearing.d. Adjust upper guide to just clear workpiece.e. Secure workpiece firmly against table.1. Read and understand the warnings posted onthe machine and in this manual. Failure tocomply with all of these warnings may causeserious injury.2. Replace warning labels if they becomeobscured or removed.3. Do not use this band saw for other than itsintended use. If used for other purposes, JETdisclaims any real or implied warranty and holdsitself harmless from any injury that may resultfrom that use.4. Always wear ANSI Z87.1 approved safetyglasses or face shield while using this bandsaw. (Everyday eyeglasses only have impactresistant lenses; they are not safety glasses.)5. Before operating this machine, remove tie,rings, watches and other jewelry, and rollsleeves up past the elbows. Do not wear looseclothing. Confine long hair. Non-slip footwear oranti-skid floor strips are recommended. Do notwear gloves.6. Wear hearing protection (plugs or muffs) duringextended periods of operation.7. Do not operate this machine while tired or underthe influence of drugs, alcohol or anymedication.8. Reduce the risk of unintentional starting. Makesure switch is in off position before plugging in.9. Make certain the machine is properly grounded.10. Make all machine adjustments or maintenancewith the machine unplugged from the powersource.11. Remove adjusting keys and wrenches. Form ahabit of checking to see that keys and adjustingwrenches are removed from the machinebefore turning it on.12. Keep safety guards in place at all times whenthe machine is in use. If removed formaintenance purposes, use extreme cautionand replace the guards immediately aftercompletion of maintenance.13. Check damaged parts. Before further use of themachine, a guard or other part that is damagedshould be carefully checked to determine that itwill operate properly and perform its intendedfunction. Check for alignment of moving parts,binding of moving parts, breakage of parts,mounting and any other conditions that mayaffect its operation. A guard or other part that isdamaged should be properly repaired orreplaced.14. Provide for adequate space surrounding workarea and non-glare, overhead lighting.15. Keep work area clean. Keep floor around themachine free of scrap material, oil and grease.Cluttered areas and benches invite accidents.16. Keep visitors a safe distance from the workarea. Keep children away.17. Make your workshop child-proof with padlocks,master switches or by removing starter keys.18. Give your work undivided attention. Lookingaround, carrying on a conversation and “horse-play” are careless acts that can result in seriousinjury.19. Maintain a balanced stance at all times so thatyou do not fall into the blade or other movingparts. Do not overreach or use excessive forceto perform any machine operation.20. Use the right tool at the correct speed and feedrate. Do not force a tool or attachment to do ajob for which it was not designed. The right toolwill do the job better and more safely.21. Use recommended accessories; improperaccessories may be hazardous.22. Maintain tools with care. Keep saw bladessharp and clean for the best and safestperformance. Follow instructions for lubricatingand changing accessories.23. Turn off the machine before cleaning. Use abrush to remove chips or debris — do not useyour hands.24. Do not stand on the machine. Serious injurycould occur if the machine tips over, or if thecutting tool is unintentionally contacted.