OneStart

Menu

Acer ARMC_2 User Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 preview
Contents
  1. revision history
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. technical support
  6. optional components
  7. Chapter 1 Introduction
  8. Important NOTES
  9. Chapter 2 Installing Your ARMC/2 Card
  10. Step 1 Unpack the ARMC/2 Card (and check jumper settings)
  11. JP4 and JP5 Chassis/Motherboard Power Switch
  12. JP12 Diagnostic and Recovery Mode Jumper
  13. J5 IPMB (Intelligent Platform Management Bus)
  14. J9 ARMC/2 Feature Connector
  15. JP6 ARMC/2 Reset Button
  16. Step 4 Confirm the Motherboard's BIOS Settings
  17. Installing Virtual Floppy Drivers on Microsoft® Windows Operating Systems
  18. Step 6 Install the Acer ARMC/2 Windows Software Components
  19. Step 7 Setup Your Client Internet Browser
  20. Step 8 Connect to the ARMC/2 from a Client System
  21. Step 9 Load the ARMC/2 SDR and Soft Processor (SP) File for Your Server Board Model
  22. Chapter 3 Locating Your ARMC/2 Card
  23. IP Address Range
  24. Usage
  25. Chapter 4 Using Your ARMC/2
  26. ARMC/2 GUI Explained
  27. Quick Launch Icons
  28. Manage Group
  29. Remote Console
  30. Redirection
  31. Staring Redirection
  32. Remote Console Shortcut Key Combinations
  33. Console Redirection Window
  34. Console Redirection Toolbar
  35. Console Redirection Toolbar Toggle Buttons
  36. Start CD-ROM Drive Redirection
  37. Stop CD-ROM Drive Redirection
  38. Start Floppy Drive Redirection
  39. Stop Floppy Drive Redirection
  40. ARMC2 Floppy Image Creator
  41. Transferring a Floppy Image to a Floppy Disk
  42. Remote Power Control
  43. Upgrade Firmware
  44. Updating Your ARMC/2's Firmware
  45. Reset ARMC/2
  46. Configure Group
  47. Users
  48. Adding Users
  49. Removing Users
  50. Viewing and Editing Users
  51. Network
  52. Firewall
  53. Alert Notification
  54. Date & Time
  55. Serial Port
  56. SSL Certificate
  57. PMCP File Upload
  58. IPMI Configuration
  59. Server OS Monitoring & Recovery
  60. View Group
  61. ARMC/2 Card Health
  62. Event Log
  63. Server Health
  64. General Information
  65. General Information : Features
  66. Last Saved Crash Screen
  67. Appendix A ARMC/2 Universal Cable
  68. Overview
  69. User Manager Tab
  70. Adding a User
  71. User Properties
  72. Network Configuration Tab
  73. Advanced Tab
  74. WinCuri
  75. LinCuri
  76. LinCuri Help File
  77. ARMC/2 Card Remote Recovery Application (RRA)
  78. Screen Distortion
  79. Solution
  80. BMC Not Responding
  81. Cannot Power On the Host System Remotely
  82. Appendix E Serial Over LAN
  83. BIOS
  84. Appendix F Port Usage
  85. Appendix G MAC Address Map
  86. ARMC/2 CD
  87. Installation
  88. Notes
Acer ARMC_2 User Manual Manual pdf 21 page image
Step 5 Install the Operating System and ARMC/2 Drivers, ContinuedInstalling Virtual Floppy Drivers on Microsoft® Windows Operating Systems, ContinuedStep Action2 The Hardware Update Wizard begins to search for the drives on the ARMC/2 CD.Note: Do NOT use the default file that the Microsoft® Windows operating system presents when it issearching for the Virtual Floppy driver. Instead, select the Specify a Location option and selectthe .INF file located in the ARMC/2 CD called amivirtfl.inf in the INF directory.3 The Hardware Update Wizard begins to load the Virtual Floppy driver from the ARMC/2 CD. Its statusis displayed.Cont’dChapter Two : Installing Your ARMC/2 Card 13
/ 153
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved